Die vorliegende Arbeit behandelt die Entwicklung einer fortgeschrittenen Technologie für die Ammoniaksynthese mit nachhaltigen Methoden, z.B. ein elektrokatalytischer Prozess mit N2, H2O und erneuerbaren Energiequellen. Die Implementierung dieser Technologie wird somit zu einem Durchbruch in Richtung einer nachhaltigen, kohlenstoffarmen chemischen Produktion führen. Die obengenannte Produktion basiert auf den erneuerbaren Energiequellen. Das Interesse an der fossilkraftstoffreien Ammoniak-Direktsynthese nimmt daher zu. Die Elektrochemische Durchflusszelle wurde für die direkte Ammoniaksynthese von Wasser und N2 bei Raum-Temperatur und Luftdruck entwickelt. Eisenoxyd Fe2O3, das auf Carbon Nanotubes (CNTs) basiert, wurde als Elektrokatalysator in dieser Hemizelle verwendet. Eine Ammoniakbildungsgeschindigkeit von 2.2×10-3 gNH3·m-2·h-1 wurde bei Raumtemperatur und Luftdruck in Anwesenheit von Stickstoff unter einem angelegten Potential von -2.0 V vs. Ag/AgCl erhalten. Dieser Wert ist höher als die Ammoniakbildungsgeschwindigkeit, die mit Edelmetallen (Ru/C) unter vergleichbaren Reaktionsbedingungen erreicht wird. Darüber hinaus wurde Wasserstoffgas mit einem Gesamtwirkungsgrad von 95.1% erreicht. Die Reaktionsbedingungen wurden mit Fe2O3-CNT (30 Gew.-%) als Elektrokatalys ator optimiert. Dieser Eisenoxidgehalt erwies sich als optimal. Die Leistungen hängen stark vom Reaktordesign ab, wobei die Möglichkeit eines Ammoniak Durchgangs durch die Membran verhindert werden muss. Die Reaktionsbedingungen spielen auch eine wichtige Rolle. Die Wirkung des Elektrolyten (Typ, pH-Wert, Konzentration), Stromdichte, Ammoniakbildungsgeschwindigkeit und Faraday'scher Wirkungsgrad in kontinuierlichen Tests bis zu 24 Stunden am Tag wurden untersucht. Die Nebenreaktion der H+/e- Rekombination zur H2 Erzeugung ist in Konkurrenz mit der direkten Ammoniaksynthese und bring zur Reduzierung aktivierter N2-Spezies. Die aktiven xii Zentern möglicherweise befindet sich an der Grenzfläche zwischen Eisenoxid und funktionalisierten CNTs. Die Aktiven Zentern für die Ammoniaksynthese wurden ebenfalls in dieser Arbeit untersucht. Wir zeigen hier, dass entgegen den Erwartungen, Eisenoxid (Fe2O3) Nanopartikel auf CNTs als Traeger hohe Umwandlungsgeschwindigkeiten von N2 mit H2O fuer die elektrokatalytisch Ammoniaksynthese zeigen. Es wird eine lineare Beziehung zwischen der Ammoniakbildungsgeschwindikeit und dem spezifischen XPS (Röntgen-Photoelektronen Spektroskopie) –Sauerstoffsignal in Bezug auf O2- in Fe2O3 Zentern dargestellt. HRTEM (Hochaufgelöste Transmissionselektronenmikroskopie) Daten über die Veränderungen während der elektrokatalytischen Tests bestätigten, dass in-situ aktivierte rekonstruierte Eisenoxidpartikel Zentern für die Ammoniaksynthese gebildet wurden. Das eröffnet neue Möglichkeiten, den Reaktionsmechanismus unter Arbeitsbedingungen zu verstehen um einen effizienten Elektrokatalysator für die Ammoniaksynthese zu entwickeln. Homogene Katalysatoren für die Ammoniaksynthese wurden ebenso untersucht. Mehrere Ruthenium-Komplexe wurden unter den gleichen Bedingungen getestet. Ru(PNP)Cl2 (PNP: 2,6-Bis[(di-tert-butylphosphanyl)methyl]pyridine) erwies sich als der beste Katalysator für die Ammoniaksynthese. verschiedene Bedingungen wurden untersucht und es wurde festgestellt, dass eine geeignete Menge Essigsäure die katalytische Leistung erhöhen kann. Wenn man verschiedene Zusammensetzungen von Stickstoff- und Wasserstoff vegleicht, wurde festgestellt, dass die Ammoniakbildung mit zunehmender Stickstoffbelastung zunimmt, woraus wir ableiten können, dass die Wasserstoff Aktivierung nicht der geschwindigkeitsbegrenzende Step unter diesen Bedingungen war.

The present Ph.D. thesis was focused on the development of advanced technics for ammonia synthesis with sustainable methods, i.e. electrocatalytic processes using N2, H2O and renewable energy as input sources. Implementing this technology will thus result in a breakthrough change towards a sustainable, low-carbon chemical production based on the use of renewable energy sources. There is thus a rising interest in fossil-fuel-free direct ammonia synthesis. A flow electrochemical cell was developed for ammonia synthesis directly from water and N2 at room temperature and atmospheric pressure. Iron supported on carbon nanotubes (CNTs) was used as the electrocatalyst in this hemi-cell. An ammonia formation rate of 2.2×10-3 gNH3·m-2·h-1 was obtained at room temperature and atmospheric pressure in a flow of N2, under an applied potential of -2.0 V vs. Ag/AgCl. This value is higher than the ammonia formation rate obtained using noble metals (Ru/C) under comparable reaction conditions. Furthermore, hydrogen gas with total Faraday efficiency as high as 95.1% was obtained. Reaction condition was optimised with Fe2O3-CNT used as electrocatalyst. A 30% wt iron-oxide loading was found to be optimal. The performances greatly depend on the cell design, where the possibility of ammonia crossover through the membrane has to be inhibited. The reaction conditions also play a significant role. The effect of electrolyte (type, pH, concentration) was investigated in terms of current density, rate of ammonia formation and Faradaic efficiency in continuous tests up to 24h of time on stream. A complex effect of the applied voltage was observed. An excellent stability was found for an applied voltage of -1.0 V vs. Ag/AgCl. At higher negative applied voltages, the ammonia formation rate and Faradaic selectivity are higher, but with a change of the catalytic performances, although the current densities remain constant for at least 24h. This effect is interpreted in terms of reduction of the iron-oxide species vii above a negative voltage threshold, which enhances the side reaction of H+/e- recombination to generate H2 rather than their use to reduce activated N2 species, possibly located at the interface between iron-oxide and functionalized CNTs. Active sites for ammonia synthesis was also explored. We show here that, contrary to expectations, iron-oxide (Fe2O3) nanoparticles (supported over carbon nanotubes - CNTs) result more active in the direct electrocatalytic synthesis of ammonia from N2 and H2O than the corresponding samples after reduction to form Fe or Fe2N supported nanoparticles. A linear relationship is observed between the ammonia formation rate and the specific XPS (X-ray- photoelectron spectroscopy) oxygen signal related to O2- in Fe2O3 species, which is proofed by both chemically and electrochemically reduced samples. HRTEM (high-resolution transmission electron microscopy) data on the changes during the electrocatalytic tests confirmed that in-situ activated sites for ammonia synthesis were formed, due to the reconstruction of iron oxide particles. This opens new possibilities to understand the reaction mechanism under working conditions and design more efficient electrocatalyst for ammonia synthesis. Homogenous catalysts for ammonia synthesis was also explored. A series of ruthenium complexes were tested using the same conditions. Ru(PNP)Cl2 (PNP: 2,6-Bis[(di-tert-butylphosphanyl)methyl]pyridine) was found to be the best catalyst for ammonia synthesis among the series of analyzed complexes. This complex was also tested using different conditions, and it was found that suitable amounts of acetic acid can increase its catalytic performance. Comparing different compositions of nitrogen and hydrogen loadings, it was found that the ammonia formation rate increases with increasing nitrogen loading, from which we can deduce that activation of hydrogen was not the rate limitation step in these conditions.

Il presente lavoro di tesi è stato incentrato sullo sviluppo di tecniche avanzate per la sintesi dell'ammoniaca attraverso processi sostenibili. Per fare ciò è stato realizzato un processo elettrocatalitico che utilizza N2, H2O ed energia da fonti rinnovabili. Esiste un crescente interesse per la sintesi dell'ammoniaca diretta senza l’utilizzo di combustibili fossili. L'implementazione di questa tecnologia determinerà un cambiamento radicale verso una produzione chimica sostenibile e a basse emissioni di CO2, basata sull'utilizzo di fonti energetiche rinnovabili. Una cella elettrochimica che opera in flusso è stata sviluppata per effettuare la sintesi dell'ammoniaca direttamente dall'acqua e dall’ azoto, operante a temperatura ambiente e pressione atmosferica. Il catalizzatore utilizzato è basato su nanoparticelle di Fe supportate su nanotubi di carbonio (CNT). È stata ottenuta una velocità di formazione di ammoniaca di 2,2 × 10-3 gNH3·m2·h-1 a temperatura ambiente e pressione atmosferica in un flusso di N2, sotto l’applicazione di un voltaggio costante di -2,0 V vs Ag/AgCl. Questo valore è risultato superiore al tasso di formazione di ammoniaca ottenuto utilizzando metalli nobili (Ru / C) in condizioni di reazione comparabili. Inoltre, è stato ottenuto idrogeno con un'efficienza faraidica del 95,1%. La condizioni di reazione sono state ottimizzate per il catalizzatore a base di Fe2O3-CNT, con un carico di ossido di ferro del 30% in peso. Le prestazioni dipendono fortemente dal design della cella, in cui è necessario limitare al massimo il crossover dell'ammoniaca attraverso la membrana. Anche le condizioni di reazione hanno un ruolo significativo, l'effetto dell'elettrolita (tipo, pH, concentrazione) è stato studiato in termini di densità di corrente, velocità di formazione dell'ammoniaca ed efficienza Faradaica nei test condotti fino a 24 ore. Lo studio sulla tensione applicata è risultato complesso: è stata trovata un'eccellente stabilità per una tensione applicata di -1,0 V vs. Ag / AgCl, a tensioni più negative, la velocità di formazione dell'ammoniaca e ix l’efficienza faraidica sono più elevate, ma con un cambiamento delle prestazioni catalitiche, sebbene la densità di corrente rimanga costante per almeno 24 ore. Questo effetto è da attribuire alla riduzione delle specie di ossido di ferro al di sopra di una soglia di tensione negativa, che migliora la reazione collaterale di ricombinazione H+ / e- per generare H2 piuttosto che reagire con le specie N2 attivate, possibilmente situate all'interfaccia tra ossido di ferro e CNT funzionalizzati. Lo studio effettuato sui siti attivi mostra che, contrariamente alle aspettative, le nanoparticelle di ossido di ferro (Fe2O3) (supportate su nanotubi di carbonio - CNT) risultano più attive nella sintesi elettrocatalitica diretta di ammoniaca da N2 e H2O rispetto ai corrispondenti campioni Fe o Fe2N realizzati attraverso riduzione. Si osserva una relazione lineare tra la velocità di formazione dell'ammoniaca, e il segnale specifico dell'ossigeno all’ XPS (spettroscopia a raggi X-fotoelettronica) relativo a O2- nelle specie Fe2O3, che è comprovato da campioni sia chimicamente che elettrochimicamente ridotti. I dati HRTEM (microscopia elettronica a trasmissione ad alta risoluzione) sui cambiamenti durante i test elettrocatalitici hanno confermato che i siti attivati per la sintesi dell'ammoniaca vengono formati in situ a causa della ricostruzione di particelle di ossido di ferro. Questo apre nuove possibilità per comprendere il meccanismo di reazione in condizioni di lavoro e progettare elettrocatalizzatori più efficienti per la sintesi dell'ammoniaca. Utilizzando le stesse condizioni di reazione, sono stati anche esplorati catalizzatori omogenei per la sintesi dell'ammoniaca utilizzando una serie di complessi di Rutenio. Il catalizzatore Ru(PNT)Cl2 (PNP: 2,6-Bis[(di-tert-butylphosphanyl)methyl]pyridine) è risultato essere il miglior catalizzatore per la sintesi dell'ammoniaca in questo screening. Il catalizzatore è stato testato anche in condizioni diverse, è stato osservato che una quantità adeguata di acido acetico aumenta le sue performance catalitiche. Confrontando la diversa composizione di azoto e idrogeno, è stato riscontrato che la x formazione di ammoniaca aumenta con l'aumentare del carico di azoto, dal quale si può dedurre che l'attivazione dell'idrogeno non è il fattore limitante in queste condizioni di reazione.

Development of carbon-based catalysts for small molecule activation

CHEN, Shiming
2019-03-20

Abstract

The present Ph.D. thesis was focused on the development of advanced technics for ammonia synthesis with sustainable methods, i.e. electrocatalytic processes using N2, H2O and renewable energy as input sources. Implementing this technology will thus result in a breakthrough change towards a sustainable, low-carbon chemical production based on the use of renewable energy sources. There is thus a rising interest in fossil-fuel-free direct ammonia synthesis. A flow electrochemical cell was developed for ammonia synthesis directly from water and N2 at room temperature and atmospheric pressure. Iron supported on carbon nanotubes (CNTs) was used as the electrocatalyst in this hemi-cell. An ammonia formation rate of 2.2×10-3 gNH3·m-2·h-1 was obtained at room temperature and atmospheric pressure in a flow of N2, under an applied potential of -2.0 V vs. Ag/AgCl. This value is higher than the ammonia formation rate obtained using noble metals (Ru/C) under comparable reaction conditions. Furthermore, hydrogen gas with total Faraday efficiency as high as 95.1% was obtained. Reaction condition was optimised with Fe2O3-CNT used as electrocatalyst. A 30% wt iron-oxide loading was found to be optimal. The performances greatly depend on the cell design, where the possibility of ammonia crossover through the membrane has to be inhibited. The reaction conditions also play a significant role. The effect of electrolyte (type, pH, concentration) was investigated in terms of current density, rate of ammonia formation and Faradaic efficiency in continuous tests up to 24h of time on stream. A complex effect of the applied voltage was observed. An excellent stability was found for an applied voltage of -1.0 V vs. Ag/AgCl. At higher negative applied voltages, the ammonia formation rate and Faradaic selectivity are higher, but with a change of the catalytic performances, although the current densities remain constant for at least 24h. This effect is interpreted in terms of reduction of the iron-oxide species vii above a negative voltage threshold, which enhances the side reaction of H+/e- recombination to generate H2 rather than their use to reduce activated N2 species, possibly located at the interface between iron-oxide and functionalized CNTs. Active sites for ammonia synthesis was also explored. We show here that, contrary to expectations, iron-oxide (Fe2O3) nanoparticles (supported over carbon nanotubes - CNTs) result more active in the direct electrocatalytic synthesis of ammonia from N2 and H2O than the corresponding samples after reduction to form Fe or Fe2N supported nanoparticles. A linear relationship is observed between the ammonia formation rate and the specific XPS (X-ray- photoelectron spectroscopy) oxygen signal related to O2- in Fe2O3 species, which is proofed by both chemically and electrochemically reduced samples. HRTEM (high-resolution transmission electron microscopy) data on the changes during the electrocatalytic tests confirmed that in-situ activated sites for ammonia synthesis were formed, due to the reconstruction of iron oxide particles. This opens new possibilities to understand the reaction mechanism under working conditions and design more efficient electrocatalyst for ammonia synthesis. Homogenous catalysts for ammonia synthesis was also explored. A series of ruthenium complexes were tested using the same conditions. Ru(PNP)Cl2 (PNP: 2,6-Bis[(di-tert-butylphosphanyl)methyl]pyridine) was found to be the best catalyst for ammonia synthesis among the series of analyzed complexes. This complex was also tested using different conditions, and it was found that suitable amounts of acetic acid can increase its catalytic performance. Comparing different compositions of nitrogen and hydrogen loadings, it was found that the ammonia formation rate increases with increasing nitrogen loading, from which we can deduce that activation of hydrogen was not the rate limitation step in these conditions.
20-mar-2019
Die vorliegende Arbeit behandelt die Entwicklung einer fortgeschrittenen Technologie für die Ammoniaksynthese mit nachhaltigen Methoden, z.B. ein elektrokatalytischer Prozess mit N2, H2O und erneuerbaren Energiequellen. Die Implementierung dieser Technologie wird somit zu einem Durchbruch in Richtung einer nachhaltigen, kohlenstoffarmen chemischen Produktion führen. Die obengenannte Produktion basiert auf den erneuerbaren Energiequellen. Das Interesse an der fossilkraftstoffreien Ammoniak-Direktsynthese nimmt daher zu. Die Elektrochemische Durchflusszelle wurde für die direkte Ammoniaksynthese von Wasser und N2 bei Raum-Temperatur und Luftdruck entwickelt. Eisenoxyd Fe2O3, das auf Carbon Nanotubes (CNTs) basiert, wurde als Elektrokatalysator in dieser Hemizelle verwendet. Eine Ammoniakbildungsgeschindigkeit von 2.2×10-3 gNH3·m-2·h-1 wurde bei Raumtemperatur und Luftdruck in Anwesenheit von Stickstoff unter einem angelegten Potential von -2.0 V vs. Ag/AgCl erhalten. Dieser Wert ist höher als die Ammoniakbildungsgeschwindigkeit, die mit Edelmetallen (Ru/C) unter vergleichbaren Reaktionsbedingungen erreicht wird. Darüber hinaus wurde Wasserstoffgas mit einem Gesamtwirkungsgrad von 95.1% erreicht. Die Reaktionsbedingungen wurden mit Fe2O3-CNT (30 Gew.-%) als Elektrokatalys ator optimiert. Dieser Eisenoxidgehalt erwies sich als optimal. Die Leistungen hängen stark vom Reaktordesign ab, wobei die Möglichkeit eines Ammoniak Durchgangs durch die Membran verhindert werden muss. Die Reaktionsbedingungen spielen auch eine wichtige Rolle. Die Wirkung des Elektrolyten (Typ, pH-Wert, Konzentration), Stromdichte, Ammoniakbildungsgeschwindigkeit und Faraday'scher Wirkungsgrad in kontinuierlichen Tests bis zu 24 Stunden am Tag wurden untersucht. Die Nebenreaktion der H+/e- Rekombination zur H2 Erzeugung ist in Konkurrenz mit der direkten Ammoniaksynthese und bring zur Reduzierung aktivierter N2-Spezies. Die aktiven xii Zentern möglicherweise befindet sich an der Grenzfläche zwischen Eisenoxid und funktionalisierten CNTs. Die Aktiven Zentern für die Ammoniaksynthese wurden ebenfalls in dieser Arbeit untersucht. Wir zeigen hier, dass entgegen den Erwartungen, Eisenoxid (Fe2O3) Nanopartikel auf CNTs als Traeger hohe Umwandlungsgeschwindigkeiten von N2 mit H2O fuer die elektrokatalytisch Ammoniaksynthese zeigen. Es wird eine lineare Beziehung zwischen der Ammoniakbildungsgeschwindikeit und dem spezifischen XPS (Röntgen-Photoelektronen Spektroskopie) –Sauerstoffsignal in Bezug auf O2- in Fe2O3 Zentern dargestellt. HRTEM (Hochaufgelöste Transmissionselektronenmikroskopie) Daten über die Veränderungen während der elektrokatalytischen Tests bestätigten, dass in-situ aktivierte rekonstruierte Eisenoxidpartikel Zentern für die Ammoniaksynthese gebildet wurden. Das eröffnet neue Möglichkeiten, den Reaktionsmechanismus unter Arbeitsbedingungen zu verstehen um einen effizienten Elektrokatalysator für die Ammoniaksynthese zu entwickeln. Homogene Katalysatoren für die Ammoniaksynthese wurden ebenso untersucht. Mehrere Ruthenium-Komplexe wurden unter den gleichen Bedingungen getestet. Ru(PNP)Cl2 (PNP: 2,6-Bis[(di-tert-butylphosphanyl)methyl]pyridine) erwies sich als der beste Katalysator für die Ammoniaksynthese. verschiedene Bedingungen wurden untersucht und es wurde festgestellt, dass eine geeignete Menge Essigsäure die katalytische Leistung erhöhen kann. Wenn man verschiedene Zusammensetzungen von Stickstoff- und Wasserstoff vegleicht, wurde festgestellt, dass die Ammoniakbildung mit zunehmender Stickstoffbelastung zunimmt, woraus wir ableiten können, dass die Wasserstoff Aktivierung nicht der geschwindigkeitsbegrenzende Step unter diesen Bedingungen war.
Il presente lavoro di tesi è stato incentrato sullo sviluppo di tecniche avanzate per la sintesi dell'ammoniaca attraverso processi sostenibili. Per fare ciò è stato realizzato un processo elettrocatalitico che utilizza N2, H2O ed energia da fonti rinnovabili. Esiste un crescente interesse per la sintesi dell'ammoniaca diretta senza l’utilizzo di combustibili fossili. L'implementazione di questa tecnologia determinerà un cambiamento radicale verso una produzione chimica sostenibile e a basse emissioni di CO2, basata sull'utilizzo di fonti energetiche rinnovabili. Una cella elettrochimica che opera in flusso è stata sviluppata per effettuare la sintesi dell'ammoniaca direttamente dall'acqua e dall’ azoto, operante a temperatura ambiente e pressione atmosferica. Il catalizzatore utilizzato è basato su nanoparticelle di Fe supportate su nanotubi di carbonio (CNT). È stata ottenuta una velocità di formazione di ammoniaca di 2,2 × 10-3 gNH3·m2·h-1 a temperatura ambiente e pressione atmosferica in un flusso di N2, sotto l’applicazione di un voltaggio costante di -2,0 V vs Ag/AgCl. Questo valore è risultato superiore al tasso di formazione di ammoniaca ottenuto utilizzando metalli nobili (Ru / C) in condizioni di reazione comparabili. Inoltre, è stato ottenuto idrogeno con un'efficienza faraidica del 95,1%. La condizioni di reazione sono state ottimizzate per il catalizzatore a base di Fe2O3-CNT, con un carico di ossido di ferro del 30% in peso. Le prestazioni dipendono fortemente dal design della cella, in cui è necessario limitare al massimo il crossover dell'ammoniaca attraverso la membrana. Anche le condizioni di reazione hanno un ruolo significativo, l'effetto dell'elettrolita (tipo, pH, concentrazione) è stato studiato in termini di densità di corrente, velocità di formazione dell'ammoniaca ed efficienza Faradaica nei test condotti fino a 24 ore. Lo studio sulla tensione applicata è risultato complesso: è stata trovata un'eccellente stabilità per una tensione applicata di -1,0 V vs. Ag / AgCl, a tensioni più negative, la velocità di formazione dell'ammoniaca e ix l’efficienza faraidica sono più elevate, ma con un cambiamento delle prestazioni catalitiche, sebbene la densità di corrente rimanga costante per almeno 24 ore. Questo effetto è da attribuire alla riduzione delle specie di ossido di ferro al di sopra di una soglia di tensione negativa, che migliora la reazione collaterale di ricombinazione H+ / e- per generare H2 piuttosto che reagire con le specie N2 attivate, possibilmente situate all'interfaccia tra ossido di ferro e CNT funzionalizzati. Lo studio effettuato sui siti attivi mostra che, contrariamente alle aspettative, le nanoparticelle di ossido di ferro (Fe2O3) (supportate su nanotubi di carbonio - CNT) risultano più attive nella sintesi elettrocatalitica diretta di ammoniaca da N2 e H2O rispetto ai corrispondenti campioni Fe o Fe2N realizzati attraverso riduzione. Si osserva una relazione lineare tra la velocità di formazione dell'ammoniaca, e il segnale specifico dell'ossigeno all’ XPS (spettroscopia a raggi X-fotoelettronica) relativo a O2- nelle specie Fe2O3, che è comprovato da campioni sia chimicamente che elettrochimicamente ridotti. I dati HRTEM (microscopia elettronica a trasmissione ad alta risoluzione) sui cambiamenti durante i test elettrocatalitici hanno confermato che i siti attivati per la sintesi dell'ammoniaca vengono formati in situ a causa della ricostruzione di particelle di ossido di ferro. Questo apre nuove possibilità per comprendere il meccanismo di reazione in condizioni di lavoro e progettare elettrocatalizzatori più efficienti per la sintesi dell'ammoniaca. Utilizzando le stesse condizioni di reazione, sono stati anche esplorati catalizzatori omogenei per la sintesi dell'ammoniaca utilizzando una serie di complessi di Rutenio. Il catalizzatore Ru(PNT)Cl2 (PNP: 2,6-Bis[(di-tert-butylphosphanyl)methyl]pyridine) è risultato essere il miglior catalizzatore per la sintesi dell'ammoniaca in questo screening. Il catalizzatore è stato testato anche in condizioni diverse, è stato osservato che una quantità adeguata di acido acetico aumenta le sue performance catalitiche. Confrontando la diversa composizione di azoto e idrogeno, è stato riscontrato che la x formazione di ammoniaca aumenta con l'aumentare del carico di azoto, dal quale si può dedurre che l'attivazione dell'idrogeno non è il fattore limitante in queste condizioni di reazione.
Ammoniak · Atmosphärendruck Elektrochemie · heterogene Katalyse · aktive Zentern · homogene Katalyse · Nachhaltigkeit
ammonia · atmospheric pressure · electrochemistry · heterogeneous catalysis · active sites · homogenous catalysis · sustainable
ammoniaca · pressione atmosferica · elettrochimica · catalisi eterogenea · siti attivi · catalisi omogenea · sostenibile
File in questo prodotto:
File Dimensione Formato  
Chen phd thesis 20181108.pdf

accesso aperto

Descrizione: Tesi di Dottorato
Tipologia: Versione Editoriale (PDF)
Dimensione 4.4 MB
Formato Adobe PDF
4.4 MB Adobe PDF Visualizza/Apri
Pubblicazioni consigliate

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/11570/3137751
Citazioni
  • ???jsp.display-item.citation.pmc??? ND
  • Scopus ND
  • ???jsp.display-item.citation.isi??? ND
social impact